{"id":2204,"date":"2026-09-23T18:03:40","date_gmt":"2026-09-23T18:03:40","guid":{"rendered":"https:\/\/blog.domapphub.com\/?p=2204"},"modified":"2026-09-23T18:03:40","modified_gmt":"2026-09-23T18:03:40","slug":"common-mistakes-facade-shop-drawings","status":"publish","type":"post","link":"https:\/\/blog.domapphub.com\/en\/blog\/common-mistakes-facade-shop-drawings\/","title":{"rendered":"5 Common Mistakes in Facade Shop Drawings (and How to Avoid Them)"},"content":{"rendered":"

Every one of the five mistakes below has, at some fabricator, turned a profitable order into a break-even one. Cracked corners at the folding table, misaligned brackets discovered mid-installation, glazing pockets that don’t match the specified panel \u2014 these aren’t abstract risks. They are recurring, specific failure points in facade shop drawings, and each one has a real cost in wasted material and idle machine time.<\/span><\/p>\n

This guide names five of the most common shop drawing mistakes precisely \u2014 and explains exactly how proper QA\/QC catches each one before it reaches your factory floor.<\/span><\/p>\n

What Are the Most Common Mistakes in Facade Shop Drawings?<\/b><\/h3>\n

The most common facade shop drawing mistakes include incorrect bolt\/bracket spacing, missed sealant joint widths, unresolved MEP clashes, inconsistent dimensioning between sheets, and missing fabrication tolerances \u2014 each of which can halt production or cause on-site rework.<\/span><\/p>\n

    \n
  1. Incorrect bracket spacing \u2014 compromises the structural connection between the facade frame and the building, often only discovered once fabrication or installation is already underway.<\/span><\/li>\n
  2. Missed sealant joint width \u2014 leads to water infiltration risk that surfaces long after handover, when it’s far more expensive to fix.<\/span><\/li>\n
  3. Unresolved MEP or structural clashes \u2014 brackets or fixings that were never checked against other building systems, causing on-site rework.<\/span><\/li>\n
  4. Inconsistent dimensioning between sheets \u2014 a mismatch between the plan view and the section detail that the factory only catches mid-production.<\/span><\/li>\n
  5. Missing fabrication tolerances \u2014 drawings that specify a nominal dimension without the tolerance a CNC machine actually needs to produce a usable part.<\/span><\/li>\n<\/ol>\n

    The Engineering Diagnosis<\/b><\/h2>\n

    From Diagnosis to Certainty<\/b><\/h2>\n

    None of these five mistakes are inevitable. Every one of them is catchable \u2014 provided the drafting office producing the shop drawing has an internal QA\/QC process built specifically to check for them before the drawing is released.<\/span><\/p>\n

    DOME FDH’s QA\/QC Process \u2014 Where These Errors Get Caught<\/b><\/h3>\n

    DOME FDH’s shop drawing process includes an internal QA\/QC review pass by the on-ground Saudi-based engineering team before any drawing package reaches a client’s factory floor.<\/span><\/p>\n

    This means bracket spacing, joint widths, cross-system coordination, and dimensional consistency are checked as a standard part of the process \u2014 not as an optional add-on requested after a problem has already surfaced in production.<\/span><\/p>\n

    The cost of these five mistakes is not hypothetical \u2014 it’s measured in scrapped material, idle CNC time, and rework on site. Catching them before a drawing leaves the drafting stage is one of the highest-leverage quality checks in the entire facade fabrication process.<\/span><\/p>\n

    Get a Second Opinion on Your Shop Drawings before they reach your factory floor.<\/b><\/p>\n

    Engineered FAQ<\/b><\/h3>\n

    Which shop drawing mistake causes the most expensive rework?<\/b><\/p>\n

    Incorrect bracket spacing is typically the costliest, since it can compromise structural connection points discovered only after fabrication.<\/span><\/p>\n

    Can shop drawing mistakes be caught before fabrication starts?<\/b><\/p>\n

    Yes, through a dedicated internal QA\/QC review pass before drawings are released to the factory.<\/span><\/p>\n

    Does DOME FDH offer a review of shop drawings prepared by another office?<\/b><\/p>\n

    Yes, this falls under DOME FDH’s design review services for facade drawings.<\/span><\/p>\n","protected":false},"excerpt":{"rendered":"

    Every one of the five mistakes below has, at some fabricator, turned a profitable order into a break-even one. Cracked corners at the folding table, misaligned brackets discovered mid-installation, glazing pockets that don’t match the specified panel \u2014 these aren’t abstract risks. They are recurring, specific failure points in facade shop drawings, and each one […]<\/p>\n","protected":false},"author":2,"featured_media":2205,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[11],"tags":[],"class_list":["post-2204","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-uncategorized-en"],"_links":{"self":[{"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/posts\/2204","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/comments?post=2204"}],"version-history":[{"count":2,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/posts\/2204\/revisions"}],"predecessor-version":[{"id":2207,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/posts\/2204\/revisions\/2207"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/media\/2205"}],"wp:attachment":[{"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/media?parent=2204"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/categories?post=2204"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/blog.domapphub.com\/en\/wp-json\/wp\/v2\/tags?post=2204"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}